QB701-B SeriesQseven BoardUser’s ManualA19730301
110IntroductionHumidityPCB• 10% to 90%• Dimensions - Qseven form factor - 70mm (2.76”) x 70mm (2.76”)• Compliance - Qseven specification revisio
111IntroductionFeatures DDR2DDR2 is a higher performance DDR technology whose data transfer rate delivers bandwidth of 4.3 GB per second and beyond. T
122Hardware InstallationBoard LayoutChapter 2 - Hardware InstallationTop ViewBottom ViewSPI Flash16Mbit BIOSIntelEG20TPCHMicrelKSZ9021RNIIntel Atom E6
132Hardware InstallationMechanical Diagram
142Hardware InstallationSystem MemoryImportant:Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in boards, and other c
152Hardware InstallationCooling OptionHeat Sink with Cooling Fan• “1”, “2” and “3“ denote the locations of the thermal pads designed to contact the c
162Hardware InstallationDimensions
172Hardware InstallationMXM ConnectorThe MXM connector is used to interface with the carrier board. Insert QB701-B series to the MXM connector on the
182Hardware InstallationDNG2 DNG 13 GBE_EBG4-3IDM_MDI2-5 GBE_EBG6+3IDM_MDI2+7 GBE_LINK100-(NC)EBG8 _LINK1000-(NC)9 GBE_EBG01-1IDM_MDI0-11 GBE_EBG21+1I
192Hardware Installation115 LVDS_SDVL611 -3A_B3-(NC)DNG811 DNG 711119 LVDS_A_SDVL021 +KLC_B_CLK+(NC)121 LVDS_A_SDVL221 -KLC_B_CLK-(NC)123 LVDS_BLT_CTR
CopyrightThis publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to
202Hardware InstallationInstalling QB701-B Series onto a Carrier Board1. The photo below shows the locations of the mounting holes and the bolts al-r
212Hardware Installation3. Press down QB701-B Series and put on the heat sink on top of QB701-B Se-ries with its mounting holes and bolts aligned on
223BIOS SetupChapter 3 - BIOS SetupOverview The BIOS is a program that takes care of the basic level of communication be-tween the CPU and peripherals
233BIOS SetupLegendsKeysRight and Left arrowsUp and Down arrows<Esc>+ (plus key)- (minus key)Tab<F1><F4><Enter>FunctionMoves t
243BIOS SetupMainThe Main menu is the fi rst screen that you will see when you enter the BIOS Setup Utility. System DateThe date format is <day>,
253BIOS SetupAdvanced The Advanced menu allows you to confi gure your system for basic operation. Some entries are defaults required by the system boar
263BIOS SetupACPI SettingsThis section is used to confi gure the ACPI Settings.Select the highest ACPI sleep state the system will enter, when the SUSP
273BIOS SetupTrusting Computing (option) This section confi gures settings relevant to Trusting Computing innovations.Aptio Setup Utility - Copyright (
283BIOS SetupCPU Confi gurationThis section is used to confi gure the CPU. It will also display the detected CPU information.Enable or Disable Intel(R)
293BIOS SetupSDIO Confi gurationThis section is used to confi gure the SDIO.Auto Option: accesss SD device in DMA mode if controller supports it, otherw
FCC and DOC Statement on Class BThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 o
303BIOS SetupUSB Confi gurationThis section is used to confi gure USB.Legacy USB SupportEnabled Enables legacy USB.Auto Disables support for legacy whe
313BIOS SetupModule Board H/W MonitorThe fi elds in this section are used to monitor the module board.Fan1 Mode SettingsConfi gure the fan mode.Confi gur
323BIOS SetupSuper IO Confi gurationThis section is used to confi gure the I/O functions supported by the onboard Super I/O chip.Restore AC Power Loss
333BIOS SetupEnable or Disable Serial Port (COM)Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.Version 2.14.1219. Copyright (C) 201
343BIOS SetupCarrier Board H/W MonitorThe fi elds in this section are used to monitor the carrier board.Enabled/ Disabled case open warning functionApt
353BIOS SetupChipsetConfi gures relevant chipset functions.Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.Version 2.14.1219. Copyrig
363BIOS SetupNorth Bridge Chipset Confi gurationConfi gure Intel IGFX Settings. Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.Versio
373BIOS SetupSouth Bridge Chipset Confi gurationConfi gure Intel IGFX Settings. Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.Versio
383BIOS SetupAptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.PCI Expr
393BIOS SetupSetup Prompt TimeoutSelects the number of seconds to wait for the setup activation key. 65535(0xFFFF) denotes indefi nite waiting.Bootup N
14IntroductionTable of ContentsCopyright ...2Trademarks ...
403BIOS SetupSecuritySet Setup Administrator Password.Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.Version 2.14.1219. Copyright (
413BIOS SetupSave & ExitReset the system after saving the changes. Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.Version 2.14.
423BIOS SetupUpdating the BIOSTo update the BIOS, you will need the new BIOS fi le and a fl ash utility, AFUDOS.EXE. Please contact technical support or
434Supported SoftwareThe CD that came with the system board contains drivers, utilities and software applications required to enhance the performance
444Supported SoftwareIntel Chipset Software Installation UtilityThe Intel Chipset Device Software is used for updating Windows® INF fi les so that the
454Supported Software3. Go through the readme document for system re-quirements and installation tips then click Next.4. Setup is now installing the
464Supported SoftwareIntel Graphics Drivers To install the driver, click “Intel Graphics Drivers” on the main menu. 3. Go through the readme document
474Supported Software4. Setup is currently installing the driver. After installation has completed, click Next.5. Click “Yes, I want to restart this
484Supported SoftwareAudio Drivers (for Q7-100 carrier board)To install the driver, click “Audio Drivers” on the main menu.1. Setup is now ready to i
494Supported SoftwareIntel Platform Controller Hub EG20t DriversTo install the driver, click “Intel Platform Controller Hub EG20t Drivers” on the main
15IntroductionAppendix A - NLITE and AHCI Installation Guide ... 58nLite ...
504Supported Software4. Click Next.5. Click Install to begin instal-lation.6. Wait until the driver is being installed, then click Next.
514Supported Software7. Click Continue Anyway or Stop Installation.8. Click Finish to exit installa-tion.
524Supported SoftwareDFI UtilityDFI Utility provides information about the board, HW Health, Watchdog, DIO, and Backlight. To access the utility, clic
534Supported Software4. Click Install to begin the installation.5. After completing installa-tion, click Finish.3. Enter “User Name” and “Organization
544Supported SoftwareThe DFI Utility icon will appear on the desktop. Double-click the icon to open the utility.
554Supported SoftwareF6 Floppy Configuration UtilityThis is used to create a fl oppy driver diskette needed when you install Windows® XP using the F6 i
564Supported SoftwareAdobe Acrobat Reader 9.3To install the reader, click “Adobe Acrobat Reader 9.3” on the main menu.1. Click Next to install or cli
574Supported Software3. Click Finish to exit installa-tion.
58ANLITE and AHCI Installation GuideAppendix A - NLITE and AHCI Installation GuidenLitenLite is an application program that allows you to customize yo
59ANLITE and AHCI Installation Guide4. Insert the XP installation disc into an optical drive.5. Launch nLite. The Welcome screen will appear. Click
16IntroductionAbout this ManualAn electronic file of this manual is included in the CD. To view the user’s manual in the CD, insert the CD into a CD-R
60ANLITE and AHCI Installation Guide7. Click Next.8. In the Task Selection dia-log box, click Drivers and Bootable ISO. Click Next.
61ANLITE and AHCI Installation Guide9. Click Insert and then se-lect Multiple driver folder to select the drivers you will integrate. Click Next.10.
62ANLITE and AHCI Installation Guide11. If you are uncertain of the southbridge chip used on your motherboard, se-lect all RAID/AHCI con-trollers
63ANLITE and AHCI Installation Guide13. The program is currently integrating the drivers and applying changes to the installation.14. When the prog
64ANLITE and AHCI Installation Guide15. To create an image, select the Create Image mode under the General section and then click Next.16. Or yo
65ANLITE and AHCI Installation Guide17. You have fi nished custom-izing the Windows XP in-stallation disc. Click Fin-ish. Enter the BIOS utility t
66ANLITE and AHCI Installation GuideAHCIThe installation steps below will guide you in confi guring your SATA drive to AHCI mode.1. Enter the BIOS uti
67ANLITE and AHCI Installation Guide5. In the Hardware Update Wizard dialog box, select “No, not this time” then click Next.6. Select “Install from a
68ANLITE and AHCI Installation Guide8. Click “Have Disk”.9. Select C:\AHCI\iaAHCI.inf and then click Open.10. Select the appropriate AHCI Controller
69ANLITE and AHCI Installation Guide11. A warning message ap-peared because the se-lected SATA controller did not match your hardware device. Ig
17IntroductionStatic Electricity PrecautionsIt is quite easy to inadvertently damage your PC, system board, components or devices even before installi
C70System Error MessageWhen the BIOS encounters an error that requires the user to correct something, either a beep code will sound or a message will
C71TroubleshootingTroubleshooting ChecklistThis chapter of the manual is designed to help you with problems that you may encounter with your personal
C72TroubleshootingThe picture seems to be constantly moving. 1. The monitor has lost its vertical sync. Adjust the monitor’s vertical sync.2. Move a
C73TroubleshootingSerial PortThe serial device (modem, printer) doesn’t output anything or is out-putting garbled characters.1. Make sure that the s
18IntroductionAbout the PackageThe package contains the following items. If any of these items are missing or damaged, please contact your dealer or s
19IntroductionChipsetExpansionInterfacesGraphicsAudioLANSDIO/MMC Serial ATABIOSEnergy EfficientDesignPowerTPM (option)Watchdog Timer Chapter 1 - Intro
Comments to this Manuals