DFI Q7-951 User Manual

Q7-951Qseven Carrier BoardUser’s ManualA14720205

110IntroductionI/O ConnectorsExpansion SlotsBoard to boardConnectorsPCB• 2connectorsfor4externalUSB2.0/1.1ports• 1connectorforanexternal

112Hardware InstallationSystem Board LayoutChapter 2 - Hardware InstallationVGACOM 1DIO11DIOpowerUSB 0USB 1LANLine-out1717SATA 1SATA 0RealtekALC262Fro

122Hardware InstallationJumper SettingsCOM2 RS232/RS422/RS485 Select1-2 On: RS232(default)3-4 On: RS422Full Duplex5-6 On: RS485JP1 is used to congure

132Hardware InstallationJP3 (for USB 0-1) and JP4 (for USB 2-5) are used to select the power of the USB ports. Selecting +5V_standby will allow y

142Hardware InstallationPanel Power SelectJP5JP5 is used to select the power supplied to the LCD panel.Important:Before powering-on the system, ma

152Hardware InstallationSuper IO SelectJP63123122-3 On: Disable (default)1-2 On: EnableJP6 is used to select enable or disable the super IO select.

162Hardware InstallationPower-on SelectJP231312-3 On: Power-on After G3 (default)1-2 On: Power-on via power button To power-on after G3:1. Set JP2 pi

172Hardware InstallationBacklight Control Level SelectJP73123122-3 On: +3.3V1-2 On: +5V (default)JP7isusedtoselectthebacklightcontrollevel+5V

182Hardware InstallationAT Mode SelectSW11 Off: Disable (default)1 On: EnableSW1 is used to select switch 1 to enable or disable the function.1ON2 3 4

192Hardware InstallationRear Panel I/O PortsThe rear panel I/O ports consist of the following:• DC-in• VGA port• COM1 port• LAN port• 2 USB

CopyrightThis publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to

202Hardware InstallationDC-in 12VThis jack provides maximum of 60W power and is considered a low power solu-tion. Connect a DC power cord to this jack

212Hardware InstallationCOM 1The system board is equipped with 1 onboard serial port (COM 1). It is also equipped with a 9-pin connector

222Hardware InstallationThe VGA port is used for connecting a VGA monitor. Connect the monitor’s 15-pin D-shell cable connector to the VGA port.

232Hardware InstallationRJ45 LAN PortThe onboard RJ45 LAN port allows the system board to connect to a local area network by means of a

242Hardware InstallationUniversal Serial Bus ConnectorsUSB allows data exchange between your computer and a wide range of simulta-neously

252Hardware InstallationAudio Front audio10MicMic PowerAuD_R_OutN. C.AuD_L_OutGNDAuD_VccKey91AuD_R_ReturnAuD_L_Return2Line-outThis jack is used to con

262Hardware InstallationI/O ConnectorsS/PDIF ConnectorThe S/PDIF connector is used to connect external S/PDIF ports. Your S/PDIF ports may

272Hardware InstallationLVDS LCD Panel ConnectorLCD/Inverter Power ConnectorThe system board allows you to connect a LCD Display Panel by

282Hardware InstallationPins13579111315171921232527293133353739FunctionGNDLVDS_Out3+LVDS_Out3-GNDLVDS_Out2+LVDS_Out2-GNDLVDS_Out1+LVDS_Out1-GNDLVDS_Ou

292Hardware InstallationDigital I/O ConnectorDigital I/O Power ConnectorThe Digital I/O connector provides powering-on function to an externa

FCC and DOC Statement on Class BThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

302Hardware InstallationMini PCIeThe Mini PCIe socket is used to install a Mini PCIe card. Mini PCIe card is a small form factor PCIe card with the sa

312Hardware InstallationThe Serial ATA connectors are used to connect Serial ATA devices. Connect one end of the Serial ATA cable to a S

322Hardware InstallationCooling Fan ConnectorsThe fan connectors are used to connect cooling fans. The cooling fans will provide adequate airow throu

332Hardware InstallationChassis Intrusion ConnectorThe board supports the chassis intrusion detection function. Connect the chas-sis intrus

342Hardware InstallationStandby Power LEDStandby Power LEDStandby Power LEDThis LED will lit red when the system is in the standby mode.

352Hardware InstallationWAN LED, LAN LED, PAN LEDActive low signals. These signals are used to allow the PCI Express, Mini Card add-in c

362Hardware InstallationFront Panel ConnectorsHDD-LED - HDD LEDThis LED will light when the hard drive is being accessed.RESET SW - Reset SwitchThis s

372Hardware InstallationThe lithium ion battery powers the real-time clock and CMOS memory. It is an auxiliary source of power when the m

382Hardware InstallationMXM ConnectorThe MXM connector is used to interface the carrier board with a Qseven board. Refer to the following

392Hardware Installation1 GND 2 GND3 GBE_MDI3- 4 GBE_MDI2-5 GBE_MDI3+ 6 GBE_MDI2+7 GBE_LINK100# 8 GBE_LINK1000#9 GBE_MDI1- 10 GBE_MDI0-11 GBE_MDI1+ 12

Table of ContentsCopyright ������������������������������������������������������������������������������������������� 2Trademarks �������������������

402Hardware Installation135GND136GND137SDVO_GREEN+138SDVO_FLDSTALL+139SDVO_GREEN-140SDVO_FLDSTALL-141GND142GND143SDVO_BLUE+144SDVO_TVCLKIN+145SDVO_BLU

412Hardware InstallationThe 1-channel I2C bus interface conforms to the version 2.1 I2C bus specication. It operates as a master or slave device and

422Hardware InstallationCan-bus ConnectorThe CAN controller performs communication in accordance with the BOSCH CAN Protocol Version 2.0B Ac

432Hardware InstallationUSB Client ConnectorThe USB client connector supports 1 port (1 USB device controller with 1 port) and high-speed (480Mbps)

442Hardware InstallationSM bus413V3SBSMB_DATAGround23SMB_CLKThe SMBus (System Management Bus) connector is used to connect SMBus devices. It is a mult

452Hardware InstallationLPC connectorThe Low Pin Count Interface was defi ned by Intel® Corporation to facilitate the in-dustry’s transition towards le

462Hardware InstallationExternal PowerThe external powered is used to support +5V and +12V for the hard drive.41+5VGroundGround23+12V

Internal I/O Connectors ... 26S/PDIF Connector ...

16IntroductionAbout this ManualAn electronic file of this manual is included in the CD. To view the user’s manual in the CD, insert the CD

17IntroductionStatic Electricity PrecautionsIt is quite easy to inadvertently damage your PC, system board, components or devices even b

18IntroductionAbout the PackageThe system board package contains the following items. If any of these items are missing or damaged, please contact you

19IntroductionChapter 1 - IntroductionSpecificationsGraphicsAudioSerial ATATPMI/O Chip Damage FreeIntelligenceTemperatureHumidityRear Panel I/OPorts•